Dec 06, 2018 Karl Storz Xenon 300 Service Manual Chrysler 300 Service Manual. The image on the right shows the military version of the EKD-500. It is shown here with the optional pre-selector / FSK demodulator on top. The EKD-500 was the successor to the EKD-300 that had been introduced in 1980. It was mechanically and electrically more robust than its. Download RFT EKD300 MODIIFICATIONS RX service manual & repair info for electronics experts Service manuals, schematics, eproms for electrical technicians This site helps you to save the Earth from electronic waste! Chrysler 300, 300C, 300 Touring & Dodge Magnum Body Repair 2004-2011 Service Repair Workshop Manual Download Pdf Chrysler 300 300C 2011-2015 Service Repair Workshop Manual Download Pdf Chrysler 300 300C With 3.6L 5.7L 6.4L 3.0D Diesel 2011-2015 Service Repair Workshop Manual. Unveiled in the 2003 New York Auto Show, the Chrysler 300 is a full-size luxury car by Daimler-Chrysler. Sales in the US began in 2005. While in Europe it was marketed since 2011 model year as Lancia Thema. It is also sold in Australia as the first full-size Chrysler vehicle since the discontinuation of Valiant in 1981.
It is big; it is heavy and built like a tank. We are talking about the EKD 500. This radio was built by 'Funkwerke Köpenick' near Berlin around 1986. At that time, there still was the DDR, the German Democratic Republic. At Funkwerke Köpenick, receivers were built which are still in use and which many shortwave listeners rave about. The EKD 500, just like its predecessor EKD 300, was widely used by radio services, mainly by the military. It certainly played a big role during the Cold War. However, the EKD 500 was also used by marine radio services and other civil agencies.
| The most important features:Frequency range: 14KHz - 30MHzTuning steps: 10Hz - 9999KHz (freely selectable)Locking rotary knobModes: AM, ECSS Synch, USB, LSB, CW, FAXBand Filter Width: 0.15-0.4--0.75.1.75.3.1-6.0-3KHz-(USB)-3KHz-(LSB)Sensitivity: 150KHz-30MHz AM 5microvolt --SSB 1.5microvoltAGC: short - long manual control for all modes99 memoriesremote controlscanning functionTracking preselectionExcellent large signal rejectionVery good frequency stabilityModular design in cassette styleExtremely stable constructionWeight: 25Kgtable-top receiver with own case |
In contrast to its predecessor, the EKD 500 could be remotely controlled with a computer. It was designed this way. It had, however, a disadvantage: A normal frequency selection like with the EKD 300 was not possible anymore. The EKD 500 only had an inconspicuous small rotary knob which stopped with quite some noise. Additionally, there were signal drop-outs caused by noise. After manual tuning for ten minutes, your hands were hurting. A real grind. This could only be remedied by two easy modifications. The scanning mechanism could easily be removed and in order to get rid of the noise drop-outs during the tuning, a resistor had to be replaced by another one on the control unit. That is rather easy to do, if you have some knowledge of electronics. However, only the 10 Hz and 100Hz tuning steps are without noise drop-outs. They are still noticeable when using tuning steps about 1KHz, but not as extreme anymore. I made these modifications myself and also installed a bigger tuning knob. Now the EKD 500 was ready for reception.
Free Ekd 300 Service Manual 2017
First, I had to learn how to operate the EKD 500. I did this based on the notes which were pasted on the front part of the radio. If, e.g., you want to change the mode or the filter widths etc., you have to enter something like a code. If you want to change to AM, you have to press the button 'MOD', followed by a '2'. If you want to change the width to 3.1 KHz, you have to press 'B' and then a '5'. For AGC -short, you press 'GC' followed by a '1'. With 'SEL' you can enable and disable the preselection. After a short while it was easy to do. |
During the few weeks that I had the EKD 500, I compared it with all receivers which were at my disposal at that time.
Starting from Long wave to the 10m-band, the EKD showed very good signal quality with steady sensitivity and little noise. The manual gain control (MGC) turned out to be the best choice. The automatic gain control (AGC) could not convince me. The decay time way too short. The noise during the speech pauses increased considerably.
Comparisons with common semiprofessional receivers, e.g., AOR AR7030, JRC NRD-525 etc showed how good the speech intelligibilty of the EKD 500 is. It proved to be better most of the time. The audio is nothing for audiophiles, stresses the pitch and has practically no bass. The intelligibility is also enhanced by the excellent mechanical and highly selective filters. A big help is also the very stable synchronic detector which synchronizes the signals in the ECSS- mode and optimizes the suppression of the noise and the crackling. Even the sidebands are selectable. But there are also negative aspects which should be mentioned.
Free Ekd 300 Service Manual Download
The EKD 500 is a professional receiver which was developed for large antennas. These antennas offer so much signal strength that the sensitivity of the receiver was a minor problem. When we connected such a receiver to one of the antennas mostly used by SWLs, e.g., a 20m long wire or a ALA1530+, we were not surprised when the EKD 500 became more and more deaf under a certain signal strength. This happened because hobby antennas simply do not have enough strength. This is the EKD's 500 weakest point.
Just like many other professional receivers, the EKD 500 does not offer any help for optimizing the signal. You will look in vain for noise blankers, notch filters or passband tuning.
The EKD has been in use for a considerable time. Although these receivers are built extremely robust and seem as if they would work for ever, you should think twice if such a boat anchor with its considerable weight on you desk is the right radio for you. Unfortunately, even the EKD 500 will break down and can cause huge repair bills. Only the shipping a 25Kg radio is not exactly cheap. There are still enough spare parts available. Some technician are specialized for these receivers and can help if problems occur.
In the pictures, you can also see the additional EZ 100. This is a preselector and has a demodulator for RTTY. It is of no use for the SWLs.
Free Ekd 300 Service Manual Pdf
Conclusions:
Free Ekd 300 Service Manual Download
A huge and heavy shortwave receiver Made in Germany. It offers very good reception with suitable (large) antennas. It is excellent as far as speech intelligibility is concerned. In any case, SWLs should modify the tuning knob
A big 'Thank you' to Reinhold Schuttkowski for loaning me his EKD 500.
Free Ekd 300 Service Manual 2016
Written at 08.11.2014
